กลับไปยังรายบอร์ด ตอบกลับ โพสต์ใหม่

iPad Wi-Fi Ըͧ

iPad Wi-Fi  Repair
            Ƿҧ¤ҧѺǡͧ iPad Wi-Fi Ѻҡͧͧͧҷҹ͡ҫҽ 鹵͹÷ӡҡҧԴѺҹ Ѻͺйٹй繻ШӤͧҡ
Review ifixit繼Ѵͪ Ambient Light Sensor ֧´ҡ Դѹѧҹ ͧǧѺ ÷ҡ Google Translate 㹡ǡѹ ¤¨Ţͧͧ


Step 1 ? Display Assembly
We are currently working on a better method to open the iPad. This method will open the iPad, but will almost certainly result in broken retaining clips.

Insert a metal spudger between the top edge of the display assembly and the rear panel assembly.

Rotate the spudger away from you to release the tabs along the top edge of the display.

Insert a second metal spudger between the top edge of the display assembly and the rear panel assembly to keep the tabs from snapping back into place.

Ҿ1 iPad Wi-Fi

meetips_iPad_Wi-Fi_01.jpg
2010-11-11 09:29


Ҿ2 iPad Wi-Fi

meetips_iPad_Wi-Fi_02.jpg
2010-11-11 09:29


Step 2
With one spudger, work your way along the right edge of the iPad, releasing tabs as you go.

Ҿ3 iPad Wi-Fi

meetips_iPad_Wi-Fi_03.jpg
2010-11-11 09:29


Ҿ4 iPad Wi-Fi

meetips_iPad_Wi-Fi_04.jpg
2010-11-11 09:29


Step 3
Lift the display assembly away from the rear panel assembly by its bottom edge.

Do not attempt to remove the display at this time, as it is attached to the rear panel assembly.

Ҿ5 iPad Wi-Fi

meetips_iPad_Wi-Fi_05.jpg
2010-11-11 09:29
มีทิปon Google+
มีทิป :
Step 7
- Disconnect the display data cable from the main board by flipping up the metal retainer by its black plastic pull tab.

Ҿ11 iPad Wi-Fi

meetips_iPad_Wi-Fi_11.jpg
2010-11-11 09:53

- Pull the cable connector away from its socket.

- Pull the connector parallel to the face of the logic board.

Ҿ12 iPad Wi-Fi

meetips_iPad_Wi-Fi_12.jpg
2010-11-11 09:53


Step 8
- Remove the display assembly from the rear panel assembly.

Ҿ13 iPad Wi-Fi

meetips_iPad_Wi-Fi_13.jpg
2010-11-11 09:53


Step 9 ? Ambient Light Sensor
- Use the edge of a plastic opening tool to carefully pry the ambient light sensor board off the adhesive securing it to the display frame.

Ҿ14 iPad Wi-Fi

meetips_iPad_Wi-Fi_14.jpg
2010-11-11 09:53


- Once you've gained enough clearance, peel the ambient light sensor off the LCD.

Ҿ15 iPad Wi-Fi

meetips_iPad_Wi-Fi_15.jpg
2010-11-11 09:53


- If necessary, attach the plastic view window to your new ambient light sensor before installation.

Ҿ16 iPad Wi-Fi

meetips_iPad_Wi-Fi_16.jpg
2010-11-11 09:53
มีทิป :
͡ѹԸiPad Wi-Fi

step 4
- In the following steps, you will disconnect the three cables attaching the display assembly to the logic board. The cables are for the following components:

Ҿ6 iPad Wi-Fi

meetips_iPad_Wi-Fi_06.jpg
2010-11-11 09:45

ᴧ Digitizer

Ambient Light Sensor

ͧ Display Data Cable


Step 5
- Use the edge of a plastic opening tool to flip up the retaining flaps holding the digitizer ribbon cables in their sockets on the logic board.

Ҿ7 iPad Wi-Fi

meetips_iPad_Wi-Fi_07.jpg
2010-11-11 09:45

- Be sure you are flipping up the retaining flap, not the socket itself.

Ҿ8 iPad Wi-Fi

meetips_iPad_Wi-Fi_08.jpg
2010-11-11 09:45

- Pull the digitizer ribbon cables straight out of their sockets.

Ҿ9 iPad Wi-Fi

meetips_iPad_Wi-Fi_09.jpg
2010-11-11 09:45


Step 6
- Use a plastic opening tool to remove the ambient light sensor connector from its socket by gently prying upward.

Ҿ10 iPad Wi-Fi

meetips_iPad_Wi-Fi_10.jpg
2010-11-11 09:45
มีทิป :
กลับไปยังรายบอร์ด ตอบกลับ โพสต์ใหม่